DT 830D Digital Multi Meter

-26% DT 830D Digital Multi Meter

OVERVIEW:

The DT830D Digital Multimeter is a very affordable and handy piece of test equipment. It features an easy to read 3.5 digit LCD display. It is equipped with 5 functions and 19 ranges, each test position isquickly and easily selected with a simple turn of the single selector switch.


FEATURES:

Small multi meter for your day to day needs

If you have basic knowledge about multi meters you can try this small multi meter for basic continuity checks and voltage measurements

When testing DC voltage, AC voltage, DC current, resistance, diode, buzzer and battery, connect the red test lead to V 0 mA jack and black test lead to COM jack

When testing the current more than 200mA, connect the red test lead to OADC jack and black test lead to COM jack

When testing the temperature, connect the temperature probe to V 0 mA jack or COM jack. Please refer to the attached instruction manual for the operating instructions.


SPECIFICATION:

Functioning

Range

Resolution

Accuracy

Overload protection

DCV

200mV

100uV

+(0.5%rdg+2dgts)

500VDC/350VAC

2000mV

1 mV

1000VDC/750VAC

20V

10mV

200V

100mV

1000V

1V

ACV

200V

100nA

+(1.2%rdg+10dgts)

750VAC

750V

1V

DCA

200μA

100nA

+(1.0%rdg+2dgts)

500mA/250V Fuse

2000μA

1μA

20mA

10μA

200mA

100μA

10A

10 mA

+(1.8%rdg+3dgts)

10A Unfused

Resistor

(ohms)

200Ω

100mΩ

+(0.8%rdg+2dgts)

Open voltage circuit approx 2.8V

2000Ω

20kΩ

10Ω

200kΩ

100Ω

2000kΩ

1kΩ


DESCRIPTION:

  • To avoid possible damage to the meter or to the equipment under test, follow these guidelines:
  • Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance.
  • Use the proper terminals, function, and range for your measurements.
  • Before measuring current, check the meter's fuses and turn power off to the circuit before connecting the meter to the circuit.
  • Before rotating the range switch to change functions, disconnect test leads from the circuit under test.
  • Before attempting to insert transistors for testing, always be sure that the test leads have been disconnected from any measurement circuits.
  • Remove test leads from the meter before opening the Meter case.
  • To avoid possible damage to the meter or to the equipment under test, follow these guidelines:
  • Disconnect circuit power and discharge all high-voltage capacitors before testing resistance, continuity, diodes, or capacitance.
  • Use the proper terminals, function, and range for your measurements.
  • Before measuring current, check the meter's fuses and turn power off to the circuit before connecting the meter to the circuit.
  • Before rotating the range switch to change functions, disconnect test leads from the circuit under test.
  • Before attempting to insert transistors for testing, always be sure that the test leads have been disconnected from any measurement circuits.
  • Remove test leads from the meter before opening the Meter case

Write a review

Note: HTML is not translated!
    Bad           Good

  • Views: 2669
  • Product Code: MTDM-02
  • Availability: In Stock
This Offer Expires In:
  • Rs340
  • Rs250
Description:BreadBoard-830 is a solderless (plug-in) breadboard with 830 connection tie-points (i.e...
Rs150
Buy all kinds of electronic products from W11 STOP. Fast delivery service, quality products with the..
Rs2
Buy all kinds of electronic products from W11 STOP. Fast delivery service, quality products with the..
Rs2
Buy all kinds of electronic products from W11 STOP. Fast delivery service, quality products with the..
Rs2